A drawing note stating “DLC coating required” does not define a functional surface. Diamond-like carbon is a family of carbon-based thin films with markedly different hardness, friction, electrical behaviour, hydrogen content and residual stress. For engineers considering how to specify DLC coatings, the task is therefore not to select a generic finish, but to translate the component’s operating conditions into measurable coating and process requirements.
This distinction matters most where failure carries a high cost: moving mechanical assemblies, precision tools, medical components, high-load contacts, optical or electronic parts, and corrosion-sensitive systems. A technically sound specification protects performance in service while giving the coating partner sufficient freedom to select a stable, repeatable process.
Start with the functional failure mode
The starting point is not coating thickness or a preferred trade name. It is the failure mechanism that limits the uncoated component. DLC may be selected to reduce adhesive wear, abrasive wear, friction, galling, particle generation or corrosion-related degradation. In other cases, the decisive requirement is biocompatibility, low outgassing, electrical insulation or a controlled level of conductivity.
These objectives can conflict. A hard, low-friction film is not automatically the best choice for a component subject to high contact stress, cyclic deformation or aggressive chemical cleaning. A very thin coating may preserve dimensional tolerances but provide insufficient wear reserve. A thicker film can improve service life, yet may increase residual stress and make edge preparation more critical.
The specification should therefore describe the application in operational terms: mating material, contact pressure, movement type, lubrication condition, temperature range, chemical exposure, target life and allowable wear. For a sliding steel component, for example, the relevant question is not simply whether DLC is hard. It is whether the chosen DLC system, counterface and lubricant regime prevent scuffing over the required duty cycle.
Define the DLC architecture, not only the material name
DLC is commonly used as an umbrella term for amorphous carbon coatings. The internal structure can range from hydrogenated amorphous carbon to tetrahedral amorphous carbon, often abbreviated as ta-C, and metal- or silicon-containing variants. Their properties differ considerably.
Hydrogenated DLC systems can provide low friction and are widely applicable on suitably prepared substrates. Hydrogen-free ta-C coatings can achieve very high hardness and wear resistance, but their higher intrinsic stress may place greater demands on substrate condition, geometry and interlayer design. Silicon-containing DLC can be advantageous in humid or lubricated contacts, while metal-containing systems may be selected where toughness, conductivity or tribological compatibility is more important than maximum hardness.
A functional specification should state the required performance envelope rather than prescribing a chemistry without context. Where a particular architecture is necessary, identify it clearly, together with the reason. Examples include a hydrogen-free carbon top layer for severe dry sliding, or a silicon-modified system for a defined lubricant and humidity range.
The bonding system deserves equal attention. On metallic substrates, adhesion is often achieved through a carefully engineered interlayer or graded transition layer. This layer may include chromium, titanium, silicon or other materials selected for the substrate and service environment. The coating stack must be considered as a system: substrate, surface preparation, interlayer and carbon top layer.
Specify substrate condition and pre-treatment
A DLC film reproduces the surface beneath it. It does not correct grinding marks, pits, inclusions, burrs or poorly controlled edge radii. Surface condition is therefore a functional requirement, not a cosmetic preference.
Define the substrate material, heat treatment condition, hardness range and finish condition. Where relevant, include the permitted surface roughness and the measurement method. A low roughness may be necessary for sealing faces or low-friction sliding, whereas a slightly different texture may be preferred for lubricant retention. The correct value depends on contact mechanics and the intended coating thickness.
Sharp edges require explicit treatment. Thin hard coatings can experience local stress concentration at unbroken edges, particularly under load. Define edge radii, deburring standards and inaccessible features before production starts. For complex parts, masking areas, internal bores, blind holes and line-of-sight limitations must also be agreed. Many PVD and plasma-assisted processes are directional to some degree, so coating distribution cannot be assumed to be uniform across every geometry.
Cleaning requirements should be controlled as part of the process route. Oils, polishing compounds, oxides and handling contamination can compromise adhesion. In regulated applications, traceability of cleaning, pre-treatment and batch handling may be as important as the final coating measurement.
Set thickness according to geometry and function
DLC coatings are commonly specified in the micrometre range, but a single thickness value without tolerance and measurement location is rarely adequate. The required thickness depends on wear mechanism, permissible dimensional change, component geometry and the deposition method.
For precision components, define the allowed dimensional build-up and nominate the critical surfaces. A coating target of, for example, 2 µm has a different consequence on a broad flat face than in a small bore or on a sharp transition. If both sides of a close-fit assembly are coated, the tolerance stack-up must be assessed before release.
State whether the requirement is a nominal thickness, a minimum thickness at accessible test locations, or a thickness range on functional surfaces. Also define the approved measurement method. Calotest, cross-sectional microscopy, X-ray fluorescence and witness coupons can each be appropriate, but they do not provide identical information. Witness samples are useful for routine process control, yet they cannot fully replace verification on representative component geometry during qualification.
How to specify DLC coatings with measurable acceptance criteria
A production-ready specification separates essential functional requirements from informative values. Hardness, for instance, is often quoted as a headline figure, but it should not be used in isolation. Nanoindentation results depend on load, indentation depth, film thickness and substrate influence. Without a defined test method and acceptance basis, hardness values from different laboratories may not be comparable.
The same principle applies to friction. Coefficients of friction vary with counterbody material, load, sliding speed, temperature, humidity, lubrication and run-in behaviour. Rather than specifying an unqualified statement such as “low friction”, define a representative tribological test or qualify the coating in the actual assembly.
Acceptance criteria should be selected according to the risk profile of the part. They may include coating thickness, surface roughness after coating, visual appearance, adhesion, hardness, elemental composition, corrosion resistance, particle generation or electrical characteristics. Not every parameter needs routine inspection on every batch. The key is to distinguish between development validation, type qualification and ongoing batch release.
For adhesion, specify the method before setting a pass criterion. Scratch testing can support development comparisons, but the critical load is affected by substrate, coating thickness, stylus geometry and test conditions. Indentation-based assessments, bend tests or application-specific mechanical tests may be more meaningful for certain component classes. The most credible evidence is often a combination of laboratory characterisation and functional testing under representative service conditions.
Define sampling, traceability and change control
For high-value or regulated components, quality cannot rely on a final inspection alone. The specification should define batch identity, sample quantities, retention of process records and the documentation required with delivery. This may include coating run identification, witness coupon results, measured thickness, inspection records and certificates of conformity.
Change control is frequently overlooked. A change in substrate supplier, alloy condition, polishing route, cleaning chemistry, fixturing or coating chamber can alter performance even when the nominal coating name remains unchanged. Define which changes require notification, requalification or customer approval. This protects reproducibility once the process is transferred from prototype quantities to serial production.
Qualify on representative components, then scale deliberately
Coupon data is necessary, but it is not the final proof of performance. A flat, polished witness coupon does not reproduce the thermal mass, edge geometry, fixturing position or surface finish of a complex production part. Qualification should therefore include representative components, or specimens that accurately reproduce the most demanding features.
The transition from prototype to volume production also requires a process capability perspective. Confirm loading density, fixturing, masking, coating distribution, handling steps and inspection capacity. If the coating process will be integrated in-house, the equipment concept must be designed around the part portfolio, required throughput, maintenance strategy and quality documentation from the outset.
NTTF approaches these projects as an interaction between coating architecture, component design and industrial process control. That is particularly relevant when standard DLC options do not meet the combined requirements for wear, adhesion, dimensional precision and reproducible scale-up.
A useful DLC specification does not attempt to dictate every deposition parameter. It defines what the component must achieve, how that performance will be verified and which process changes must remain controlled. That creates room for application-specific process development while preserving the assurance technical decision-makers need: a coating system that is qualified for the real component, not merely impressive on a data sheet.

